Nanotechnologies in Construction: A Scientific Internet-Journal

263–273

Authors: Korolev E.V., Grishina A.N., Inozemtcev A.S., Ayzenshtadt A.M.

ABSTRACT: Introduction. The study of the kinetics structure formation is rarely the subject of a careful study. Although it is important for materials used to create elements of building structures, energy elements, thermoelements and materials for other purposes. The article proposes refinements of the methodology for determining the parameters of the kinetics structure formation of cement composites, including modified compositions. Methods and materials. The structure formation of cement systems with plasticizers, microsized mineral additives (hydrosilicates of barium, copper, iron and zinc) and nanosized particles of zinc hydrosilicates has been studied. Results and discussion. It is proposed to single out two stages of initial structure formation: the stage of setting the cement paste and the stage of hardening. It was found that the strength of the material at the stage of hardening should be influenced by an additional factor, depending on the type of the introduced substance. A strong negative relationship between the parameters α and n of the equation R(t) = Rmax(1–eatn ) at the hardening stage was confirmed. The trends identified at the setting stage also demonstrated, namely: an increase in the rate of structure formation leading to the formation of a less dense structure. Conclusions. An analysis of the change in the value of the internal dimension of the system during the transition from the stage of setting to the stage of hardening made it possible to identify two trajectories of the system development. The first trajectory appears only by combining the elements of the structure (trajectory No. 1). Preservation of the characteristic dimensions of structural elements, but an increase in the proportion of elements with small dimensions (when the conditions that prevent the combination of elements of the structure are realized) describes the second trajectory (trajectory No. 2). The implementation of trajectory No. 2 is typical for compositions which the structure formation of cement stone is carried out in the presence of Melment F15G plasticizer or microsized particles of copper or zinc. For other studied compositions, structure formation is proceeding with the enlargement of structural elements.

282–293

Authors: Luojin Cao, Nianqin Liu, Xiangyu Li, Wenming Que, Yong Li

ABSTRACT: China is the kingdom of arch bridges. Based on the principle of structural elastic potential energy standing value, the innovative application of the design theory of composite arch bridge bending and compression is presented, optimize the design of composite structural arch bridge arch axis, and propose the design and construction method of medium-bearing composite Nielsen arch bridge. The design of the medium-bearing composite Nielsen arch bridge is carried out, its structural strength, stiffness and stability are analyzed by finite element analysis. By simulating the parameters of arch axis, sagittal span ratio and arch section, the convergent composite arch axis with solid web foot section is adopted to improve the economic spanning capacity of the composite Nielsen arch bridge and expand the adaptation range of large span arch bridge in plain area or soft base area

306–318

Authors: Moldamuratov Zh.N., Imambayeva R.S., Imambaev N.S., Iglikov A.A., Tattibayev S.Zh.

ABSTRACT: Introduction. Research of polymer concrete properties show that it differs favorably from conventional concrete by such indicators as mechanical strength, resistance to aggressive impact of various environments, water resistance, abrasion resistance, water-repellency and frost resistance. Currently, it is possible to obtain polymer concrete with characteristic and chemical properties –specified density, strength, deformability, ductility, and corrosion resistance. Methods and materials. The research is carried out by comparing laboratory tests of polymer concrete based on furfural binder. Furfural has a high reactivity and can form resin compounds with many chemicals. Diphenylamine was added to furfural in different proportions. Benzenesulfonic acid, sulfuric acid and their mixture at a ratio – 1:1 by weight were used as hardeners. Crushed sand or ground andesite based on nanostructured microfiller served as aggregate for various compositions of polymer solutions. The polymer concrete strength, chemical resistance, lasting properties, water resistance, abrasion resistance, metal adhesion were tested during the research. Structural changes in properties were studied by the electron microscopic analysis method. Results and discussion. It is established that the diphenylamine solution in furfural, provided that it is solidified by sulfuric acid, benzolsulfoacid or mixture of these acids, is a polymer binder capable to form a high-strength material under normal hardening conditions by acid-resistant aggregates. It is also determined that to prepare resin, the ratio of furfural and diphenylamine should be within 1:0.5–0.3 by weight. The resin containing 1 weight part (w.p.) of furfural and 0.5 weight part of diphenylamine is conventionally named FD-1; containing 1 weight part of furfural and 0.4 weight part of diphenylamine – FD-2 and resin with 0.3 weight part of diphenylamine – FD-3. Conclusion. The introduction of nanostructured microfiller into the polymer concrete composition could save expensive resin. Comparison of the technologies for producing FD resin and polymer concrete, as well as preliminary test data of the studied materials, can determine the possible technical and economic advantages of polymer concrete based on FD resin over the polymer concrete based on FA (furfurolacetone) monomer which is currently used in construction of hydro-engineering structures. Polymer concrete based on FD resin has high strength and exceeds the strength of polymer concrete based on FA monomer by 20–25%.

328–338

Authors: Xiangyu Li, Luojin Cao, Cheng Zhang, Liping Ma, Yong Li

ABSTRACT: This essay proposes a new structural system for a large span three-arch, three-cable face steel edge main beamrigid tie composite arch bridge. The authors invented a new structural form of a steel edge main girder rigid tie, and developed and designed a key arch-bar three-dimensional six-way space node structure. The analysis of results show that: compared with the traditional arch bridge, the large span three-arch three-cable face steel-sided main beam rigid ties composite arch bridgeis beautiful in shape, hasareasonable structure and efficient construction. It is a high-strength, high-performance composite structural system, with better strength, stiffness, stability and dynamic performance, which overcomes the large span ultra-wide bridge deck arch bridge horizontal thrust, poor transverse stability, and the key technical problems of acable joint control. The proposed structural form has a wide range of engineering application prospects.

176-189

Authors: Korolev E.V., Grishina A.N., Inozemtcev A.S., Ayzenshtadt A.M.

Introduction. The study of the kinetics structure formation is rarely the subject of a careful study. Although it is important for materials used to create elements of building structures, energy elements, thermoelements and materials for other purposes. The article proposes refinements of the methodology for determining the parameters of the kinetics structure formation of cement composites, including modified compositions. Methods and materials. The structure formation of cement systems with plasticizers, microsized mineral additives (hydrosilicates of barium, copper and zinc) and nanosized particles of zinc hydrosilicates has been studied. Results and discussion. It is proposed to single out two stages of initial structure formation: the stage of setting the cement paste and the stage of hardening. The selection of the setting stage is connected with the natural laws of the development of natural systems, namely, the initial formation of a structural grid obeys an exponential law. Moment of time when a deviation from this law is observed is the time of occurrence of spatial and/or prescription difficulties that hinder the exponential development of the system. Conclusions. A strong negative relationship between the parameters φ and β of the equation H(t) = a exp(φt β) has been established. These parameters characterize the rate of structure formation at the setting stage (parameter φ) and the density of the structure (parameter β or the internal dimension Di, 0 associated with it). The presence of such a negative relationship indicates the inadvisability of accelerating the processes of structure formation at the stage of setting. This is supported by a strong positive relationship between the period of initial structure formation t0, s1 and the strength of the material R28.

198-204

Authors: Qinglin Liu, Huanyu Ye, Zhihong Zhang, Rongming Wang

Metal nanocrystals exhibit unique properties due to their high surface-to-volume ratio and have great potential for applications in the fields of electronics, magnetics, optics and catalysis. However, their high specific surface area leads to easy coarsening in operation, which may greatly degrade their performances, especially when they are exposed to various chemical environments or at high temperatures. Therefore, the direct visualization of nanocrystals' structural evolution when they are coarsening is crucial to gain insight into the mechanism and develop more effective means to improve the size stability of nanocrystals. In this work, we investigated the structural evolution of Pt nanocrystals with sizes of ~ 4 nm on SiNx film in both oxidizing and reducing atmospheres at a moderate temperature (300о С) in the aberration-corrected environmental transmission electron microscopy (ETEM). The sizes of nanocrystals remain almost unchanged when annealed in the oxygen atmosphere with volatile PtOx formation on the surface, hindering nanocrystals sintering and leading to Pt loss. On the other hand, obvious coarsening of nanocrystals resulting from Ostwald-ripening and nanocrystal migration and coalescence was observed in the reducing atmosphere. Our findings reveal the dynamic structural evolution of nanocrystals in different atmospheres and provide possible ways to improve the size stability of nanocrystals

217-226

Authors: Belozerov V.V., Belozerov Vl. V.

Introduction. Recently, much attention in the publications of scientists has been paid to “nature-like technologies” in the use of RES – renewable energy sources (sun, wind, heat). At the same time, foreign business, despite the fact that these sources are low concentrated and seasonal, is actively investing in their development. In Russia, these processes have been developing slowly, and therefore, on the basis of a system analysis, it seems relevant to justify the correct vector of application of RES. The article provides evidence of the insolvency of opinions about the insufficiency of the assimilation potential of the biosphere to compensate for the economic activity of mankind. In this connection, the scientific, technical and socio-economic tasks arise for the “reengineering of the technosphere” in the structure of the life support systems of society, including educational facilities. Methods and models. To solve these scientific, technical and socio-economic issues, by analogy with individual residential buildings, it is proposed to use “nature-like nanotechnologies” in the engineering systems of schools, and for evaluation - the method of retro-forecasting the results of introduction of domestic innovations, which has proved its adequacy when solving the problems of fire and environmental safety of the technosphere in the regions of the South of Russia. Results and discussion. The results of the synthesis and “virtual implementation” of autonomous engineering systems for school buildings are presented, which allow for the decentralization of electricity, water and heat supply by generating resources (water, heat and electricity) using the “Shukhov wind-electric installations” combined with a vortex system extraction of moisture of air, with their duplication by hydro panels and solar batteries. The calculations have demonstrated that the putting into production of such domestic innovations and the «reengineering» with their help of the engineering systems of 40 thousand Russian schools will allow autonomization and proper electricity, water and heat supply, which will ensure their safe functioning in compliance with GOST 12.1.004. Moreover, after the introduction of an autonomous engineering system in the school, due to the annual savings in budget subsidies for “pedagogical services”, it becomes possible to increase the monthly salary of each school teacher by 30–40 thousand rubles. Conclusion. The conducted studies confirm the results obtained in the synthesis of autonomous engineering systems for individual residential buildings, unequivocally determining the place of RES in the structure of resource supply systems for cities and rural settlements.

241-249

Authors: Maskova A.R., Yarmukhametova G.U., Rakhmatullina R.G., Sabitov I.N., Aminova G.K.

Introduction. Polyvinyl chloride (PVC) is the world's leading synthetic polymer in industrial use. Products based on PVC have firmly taken on the world market, and currently there is no highly developed country that is able to avoid its production and consumption. The high demand for thermoplastics is primarily due to its unique properties such as durability, resistance to climatic conditions, low flammability, good barrier properties, economy, environmental friendliness and versatility. The complex of technological and service properties of soft PVC, in addition to other additives, is mainly provided by plasticizers, the content of which can reach 50% or more. It is the efficiency of the plasticizing that has a decisive impact on the characteristics in the resulting materials and products. One of the most widely used classes of compounds in the plasticization of PVC are phthalic acid esters, in particular, dibutyl phthalate (DBP), di-(2-ethylhexyl)-phthalate (dioctyl phthalate, DOP), diisononyl phthalate (DINP) and diisodecyl phthalate (DIDP). Phthalates have found the greatest use as plasticizers due to their properties: good compatibility with PVC, low migration from plastic compound, minimal interaction with the polymer at room temperature, good frost resistance, high electrical insulating properties, availability, manufacturability and low cost. Methods and materials. The paper presents methods for the obtaining of novel symmetrical and asymmetric phthalate plasticizers: dibenzoxyethyl phthalates, benzylbenzoxyethyl phthalates, phenoxyethylbenzoxyethyl phthalates, ethoxyoctylbenzoxyethyl phthalates – by catalytic esterification of phthalic anhydride with oxyethylated phenylcarbinols, phenols and 2-ethylhexanols. The conditions for the synthesis of target products with the maximum yield were selected. The physicochemical properties of the obtained compounds were studied. The obtained experimental data were used to identify promising novel plasticizers of the phthalate type by cluster analysis. Cluster analysis for decision making is the most effective, as it is designed to combine some samples into classes (clusters) in such a way that the most similar in properties get into one cluster, but at the same time, samples of different clusters differ from each other as much as possible. Clustering carried out in the program Statistica 10. Results and discussion. According to the data obtained, it is found that benzylbenzoxyethyl phthalates and ethoxyoctylbenzoxyethyl phthalates have the best characteristics in terms of plasticizing ability. We study the influence of the selected plasticizers on the physical and mechanical characteristics of PVC compositions The effectiveness of compounds in the PVC composition is evaluated in terms of “elongation stress” and “breaking stress”. The test results of the samples are compared with the indicators of PVC compounds containing DBP. Conclusion. The use of the developed additives contributes to the production of PVC compounds with improved physical and mechanical characteristics

83-88

Authors: : Kosach A.F., Kuznetsova I.N., Rashupkina M.A., Pedun G.A.

Introduction. One of the promising areas related to formation of concrete structure on the basis of a mineral binder with specified performance properties employs the addition of ultradispersed fillers (nanomodifiers) to the binder composition. Wastes of quartz and hydro-removal ash are used as nanomodifiers. The presence of nanoparticles in the binder can significantly change the processes of hydration and hardening of the concrete mix. Materials and methods. Hydro-removal ash from Omsk combined heat and power plant 5 (CHPP-5), cement and quartz waste obtained from the production of highly pure quartz concentrate which acted as an enhancer of pozzolanic activity to hydro-removal ash were used as materials for cement stone on the basis of a quartzash-cement binder. Nanomodifier was obtained as a result of mechanical, mechanohydraulic (water) and mechanohydrochemical (water + Megalit S-3ML additive) activations. Activation of the quartz-ash mixture was carried out in a continuous-action rotary mill. The mechanical method provides only mechanical activation, and the mechanohydraulic method provides mechanical, hydraulic, turbulent and acoustic activations. The mechanohydrochemical method provides all actions of hydraulic activation including chemical one. Results. The article investigated cement stone on the basis of quartz-ash-cement binder (activated quartz waste and hydraulic ash from Omsk CHPP-5, cement). The technologies of activation of the quartz-ash mixture by increasing the specific surface of the dispersed phase for the production of quartz-ash-cement binder are considered. The obtained results of the weight distribution of particles of hydro-removal ash and quartz before and after activation show that the average size of the nanoparticle diameter is from 25 µm to 1.5 µm and specific surface is 967–7729 cm2 /g. Conclusions. The use of nanoparticles in a quartz-ash mixture allows increasing the strength characteristics of cement stone from 23 to 59%. The use of quartz waste from the production of high-purity quartz concentrate and ash hydraulic removal from Omsk CHPP-5 power plant with the introduction of the proposed technologies for their activation allows increasing the formation of cement stone on a quartz-ash-cement binder by increasing the package density and chemical activity of nanoparticles in the processes of phase formation of hydrate compounds, which will reduce intergranular space between non-hydrated cement grains and will improve physical and mechanical characteristics of cement stone

96-104

Authors: Loganina V.I.

Introduction. At present, when performing finishing and restoration work, more and more preference is given to dry lime mixes (DBM). Wide opportunities for the production of dry lime-cement mixes are opened up by the use of diatomite, which is both a dry mix filler and an active mineral additive. Previous studies have confirmed the effectiveness of heat treatment of diatomite. After firing at 600–800о C, activity increases when interacting with calcium oxide hydrate. This is explained by the fact that at 600–800о C clay substances are dehydrated to metakaolinite, which is characterized by increased reactivity. The properties of dry mixtures and compositions based on them are affected by the particle size of the components of the dry mixture. In this regard, it is of great importance to study the influence of the dispersion of the components of the dry mixture on the formation of the structure of the finishing compositions. Materials and methods. To study the active centers of the diatomite surface, we used the indicator method for determining the distribution of adsorption centers. Determination of the compressive strength was carried out on a DOSM-3-1 dynamometer on samples 3x3x3 cm in size at the age of 28 days of air-dry hardening of the compositions. The determination of the granulometric composition of the components of the dry mixture was carried out by the method of sedimentation analysis. Adsorption was estimated from the optical density measured with a PEC photoelectrocalorimeter. To study adsorption at the “liquid-solid” interface, the initial components of the dry mixture, lime and diatomite, were used. Results and discussions. Accordingto the data obtained, it was found that a particle size reduction of the dry mixture filler leads to an increase in the strength characteristics of lime-diatomite compositions.It was found that the introduction of C-3 additive into the water favorsincreasing dispersion of hydrated lime, improving plasticity finishing mixture and improving the physical and mechanical characteristics lime-diatomaceous compositions.It is proposed to introduce sulfate additiveinto the formulation of the aluminumdry mixture. Increase in the compressive strength of the finishing composition with addition of aluminum sulfate 1.5–2 times was observed. Conclusion. It has been determined that the developed dry mixture is highly competitive, in terms of technological and operational properties,withprototype. Moreover, the production of the proposed DBM is more economical due to the use of local raw materials and domestic additives

119-136

Authors: Belozerov V.V., Nikulin M.A., Belozerov Vl.V.

Introduction. Recently, the term “nature-like technologies” has appeared in the everyday life of scientists and politicians, which quite deservedly include the so-called alternative energy sources (sun, wind, heat). At the same time, despite the fact that installations using these sources are “seasonal” and low concentrated, their use is rapidly and haphazardly developing, and many economists and politicians mistakenly consider them as basics, misleading business. Based on the analysis of the epistemology of the origin of the term "nature-like technologies", this article shows the groundlessness, and even the harm of the rapid and unsystematic use of wind turbines. Evidence is given of the inconsistency of the "myths" that Nature cannot cope with the compensation of the economic activity of mankind, therefore, according to Academician Sergeyev S.M., President of the Russian Academy of Sciences, "reengineering of the technosphere" is required. At the same time, modern economic science is far from taking into account in his models of the assimilation potentials of the biosphere of regions and the functions of entropy production in them, preferring to model various “cycles and modes”, as well as calculate different “coefficients” in order to predict “crises and equilibria”, without taking into account the interaction nature and society. In this connection, a scientific and technical task about determinating the “place of reengineering of the technosphere” in the structure of the life support systems of society, and, consequently, to evaluate its effectiveness. Methods, models and tools. To solve the tasks set, it is proposed to use the “retro-forecast method” of socio-economic losses from the introduction of “natural nanotechnologies”, using as “tools” the method of “spatio-temporal analysis”, model of the Leontief-Ford and adaptive taxation systems of “harm production”, the use of which in solving the problems of fire and environmental safety in the "technospheres of the regions" of the South of Russia (in road transport infrastructures, in cities and towns, in buildings and structures), proved their adequacy to the processes under study and usefulness. Results and discussion. The results of modeling the costs of efficiency of "reengineering of the technosphere" in Russia, in particular individual residential buildings, and a retro-forecast of changes in socio-economic and environmental losses during the autonomy of their resource supply (electricity, water and heat) are presented. It is shown that the production of domestic innovations in this area (“Shukhov’s” wind turbines, atmospheric water condensation devices and electric heating) will allow stopping the “total gasification” of rural settlements, as well as more economically than abroad, to implement decentralized supply of resources in Russia more than 10 million individual houses and about 40 million country houses, thus determining the “true place of alternative energy” in the structure of the Russian systems of electricity, gas, water and heat supply. Conclusion. The proposed approach allows us to determine the place of the socalled renewable energy in the structure of resource supply systems for cities and rural settlements. At the same time, it is possible that the emergence of more productive design solutions of the proposed innovations in the field of wind energy and solar panels will expand the "autonomization" to low-rise and multi-apartment buildings in regional centers and workers' settlements, instead of a major restoration of centralized engineering systems with boiler houses and mini- CHP.

145-155

Authors: Balykov A.S., Nizina T.A., Volodin S.V

Introduction. The management of physical and chemical processes of structure formation of high performance cement composites can be provided at several scale levels through the use of modifiers of various nature and mechanism of action, in particular, micro- and nanoscale mineral additives of natural and technogenic origin. It is known that clays and carbonate rocks are promising raw materials to obtain mineral modifiers for cement systems. The purpose of this study was to establish the influence regularities of the prescription and technological parameters (material and granulometric compositions, temperature calcination) to obtain mineral additives based on calcined clays and carbonate rocks on their activity in cement systems. Methods and materials. Polymineral clays and carbonate rocks (dolomite and chalk) from several deposits of the Republic of Mordovia were used as raw materials for obtaining mineral additives. The specific surface area of modifiers was determined on the PSX-12 dispersion analysis device using the Kozeny-Carman method. The study of the granulometric composition of sedimentary rock powders was carried out by laser diffraction method. The research of physical-chemical processes occurring during the heat treatment of polymineral clays and carbonate rocks was carried out using the synchronous thermal analysis method. Optimization of calcination temperature of clay-carbonate mixtures was carried out based on the research results on the effect of their additives on the cement binder activity with the determination of the modifier activity index in accordance with the methodology of the Russian State Standard GOST R 56178-2014. Results and discussion. The optimum calcination temperature, located for polymineral clays in the area of 500–800оC, was established according to the study results of dehydration processes of clay minerals using the synchronous thermal analysis. This temperature range corresponds to the initial restructuring processes in the crystal structure of minerals of the kaolinite and illite groups, associated with their dehydroxylation, which contributes to the transition of these phases to the active form. The study results of influence of additives of calcined clay-carbonate mixtures on the cement binder activity proved the thermal analysis data. It was found that calcination of clays and clay-carbonate mixtures at 700°C contributes to obtaining of the most effective mineral modifiers. Conclusions. On the totality of studies, regularities were revealed in the system “modifier composition – calcination temperature of sedimentary rocks – mixed binder activity”, which allow optimizing the prescription and technological parameters for obtaining mineral additives to achieve the required level of strength characteristics of cement composites.

5-10

Authors: Frolova M.A.

Introduction. When using water suspensions of finely dispersed mineral systems of natural and anthropogenic origins as active agents in the production of concrete composites, an important factor in their effective use is to ensure the aggregative and sedimentation stability of solid phase particles before adding the solid phase into the reaction mixture. Methods and materials. The paper provides an algorithm for quantifying stability criteria according to the DLVO theory provisions as exemplified by a suspension of fine polymineral sand powder from the Kholmogorskoye deposit in the Arkhangelsk region (average particle size is 195 nm). In order to successfully assess the aggregative stability of this colloidal system, it is necessary to conduct experiments for determining the analogue value of the Hamaker constant, which was 0.5 •10–20 J for the mineral sand studied, in addition to experiments for determining the zeta potential of particles. This paper presents the results of the analysis according to the criteria of the value of the interaction energy (Uint) and the sedimentation rate (Vsed) of a polymineral sand dispersed system (water suspension) calculated taking into account the analogue value of the Hamaker constant, zeta potential and dimensional characteristics of its solid phase particles, physicochemical properties of the dispersion medium. Results and discussion. It is shown that the determining factor of the aggregative stability of the suspension is the electrostatic barrier for particle interaction. Theoretical calculation showed that the aggregative stability of the system may be affected by its particles reaching their zeta potential of approximately 10–4 mV (a nearly isoelectric state). It is proposed to use the kinetic parameter of sedimentation – its velocity – to assess the kinetic (sedimentation) stability of this suspension – resistance to gravity, i.e. the ability to resist the dispersed system stratification due to the difference in particle densities between the dispersed phase and dispersion medium. Conclusion. The sedimentation rate is Vsed ≈ 4 nm/sec for the object under study in water dispersion medium with the averaged dimensional characteristics of 195 nm. At such a rate of solid phase particle precipitation, a dispersed system based on finely crushed polymineral sand from the Kholmogorskoye deposit can be considered sedimentatively stable.

18-26

Authors: Ivanov L.A., Xu L.D., Bokova E.S., Ishkov A.D., Borisova O.N.

Advanced technologies impress people’s imagination demonstrating the latest achievements (materials, methods, systems, technologies, devices etc.) that dramatically change the world. This, first of all, concerns nanotechnological inventions designed by scientists, engineers and specialists from different countries. Main part. The article provides an abstract overview of inventions of scientists, engineers and specialists from different countries: Germany, Iraq, China, Russia, USA, Ukraine, Sweden, Japan et al. The results of the creative activity of scientists, engineers and specialists, including inventions in the field of nanotechnology and nanomaterials allow, when introduced to industry, achieving a significant effect in construction, housing and communal services, and related sectors of the economy. For example, the invention «Nanomodified building mortar» refers to construction materials and can be used in masonry of ceramic stones, ceramic bricks, hollow bricks in dry and hot climate. The novelty, in respect to the existing construction mortars, is the combination of known components of Portland cement, sand for construction works, amorphous nanomodified silica dioxide, superplasticizer С-3, cure retarders of Portland cement, air-entraining resin. The given qualitative and quantitative composition of nanomodified construction mortar makes it possible to obtain the mentioned mixtures in a simple way: for example, in gravity mixer, with evenly distributed components in volume, which is characterized with specified flowability, water-retaining property, controlled hardening period and can be used in dry and hot climate with air temperature up to 40-50°С. The following inventions in the field of nanotechnology can also be interesting for specialists: a composition of self-compacting construction concrete on the basis of cement matrix, a method of producing polarization-sensitive nanocomposite film on the basis of copper selenide, a method of producing porous moulded article in the form of insulation plaster layer, a method to obtain amorphous nanostructured diamond-like coating, a method of cement surface modification, a system to produce carbon nanotubes, et al. Conclusion. One of the most challenging tasks the economy of every country faces is to increase industrial competitiveness through technological upgrade. From the side of the state and companies the principal object to control in this process are the people and enterprises dealing with introduction of inventions and new technologies.

43-52

Authors: Peng Dong, Jingyi Liu, Huiru Wang, Hongyan Yuan, Quan Wang

Introduction. Recent years have seen a pressing need to dispose of municipal solid waste due to rapid urbanization. The municipal solid waste incineration fly ash (MSWIFA) produced from solid waste incineration power plant exhibits pozzolanic properties and poses concern of toxicity leaching when used directly as building materials. This paper presents an alkali-activation method to produce sustainable alkali-activated MSWIFA materials (AAFMs) with various MSWIFA dosages and investigate the corresponding fabrication and performance. Materials and Methods. Composited alkali activators activate the MSWIFA with constant alkalinity of 5% and the molar ratio of Si/Na = 0.86. The resulting geopolymers' bulk densities, mineral composites, morphology, and compression strength are thoroughly examined. Results and discussions. Results show that the use of MSWIFA may lead to more loose structures because the bubbles are generated from metallic aluminum and alkali activators. Additionally, the production of multiple crystals also accounts for increasing porosity. The generated multi-crystals such as Sylvite, Halite, Hydrocalumite, Calcium Hydroxide, and Ettringite are further detected from the morphology and mineral analysis. Furthermore, compression tests and toxicity characteristic leaching procedures (TCLP) are conducted to investigate the mechanical performance and heavy metals solidification performance of AAFMs, with an optimal compression strength of 19.99MPa at 28 days for AAFM-10 while toxicity leaching is subject to regularity limits. Conclusions. This study shows that great potential of using the alkali-activation method to recycle hazardous municipal solid fly ash into construction materials with both ecological safety and high performance.

62-69

Authors: Muravieva E.A., Kulakova E.S.

Introduction. The article describes the results of a comparative analysis of three large companies presenting on the market close control equipment for the control of climatically important parameters: LI-COR, Picarro and Gasera, and using nanotechnologies; the urgency of the ecological problem of finding a technical solution for the control of climatically active gases, including CO2 in the atmospheric air, was studied. The aim of the work is to analyze the world leaders in the production of precision equipment for monitoring greenhouse gases in the manufacture of nanomaterials and in scientific centers for the study of climate change. Methods and materials. The study is based on the information from open information sources, materials and reviews of various fields of knowledge made by scientific researchers, who describe the features of the activities of these companies or are directly involved in product development, and then compile a report on their work. The article contains information from true sources, namely from the official websites of companies, which describes their history of creation and development process. Research methods are benchmarking and SWOT analysis. Results and discussion. The study carried out a comparative analysis of companies in terms of the duration of work in world markets and its impact on the quality and technical features of products. The article provides information about companies that have achieved very good results from the beginning of their foundation to the present. The species diversity of old and new generation quality control devices sold in markets around the world by the companies in question is the same, which leads to very high competition. A description of the companies’ operations, their location, coverage of consumers is given, as well as the annual income from the sale of products, the amount of work that they do in the course of their activities. Conclusion. It was revealed that the companies LI-COR, Picarro, Gasera carry out the production of quality control devices that reproduce the required measurement parameters. Gas-analyzers of the companies are in demand in the market of precision control devices used to capture greenhouse gases in order to develop building anomaterials, scientific research on the climate problems of modern society.

343-349

Authors: Massalimov I.A., Massalimov B.I., Mustafin A.G.

Introduction. Impregnation with a solution based on calcium polysulfide showed excellent results in the hydrophobization of concrete, brick and shell rock due to the formation of a water-repellent coating of sulfur nanoparticles on the surface of their pores. This paper presents the data of studying the properties of aerated concrete, widespread in construction practice, which has a widely developed pore system. Materials and methods. The data on the penetration of water into the studied samples of aerated concrete using the methods of visual examination, including electron microscopy, as well as methods for measuring the water absorption and strength of the samples impregnated with a solution based on calcium polysulfide are presented. Results. It is shown that aerated concrete impregnated with calcium polysulfide, despite the developed pore system, acquires pronounced water-repellent properties. It was found that the optimal processing time is 20 minutes, and the increase in the water-repellent properties of aerated concrete depends on the density of the impregnating solution. As a result of impregnation of aerated concrete by immersion in a solution with a density of 1.16 g/cm3, a decrease in 3.7 times occurs, and when treated with a solution with a density of 1.25 g/cm3, it decreases 6.8 times and becomes equal to 6%. For samples processed with the use of vacuum, in the case of processing a solution with a density of 1.16 g/cm3, water absorption decreases by 7.9 times, and when processing with a solution using vacuum, it decreases 19.8 times, while the compressive strength increases by 1.7 once. Samples of aerated concrete, treated with a polysulfide-based solution with a brush, showed that in this case, water absorption in the sprinkling mode decreases to values of 1.5–2.0%. Discussion. It is noted that during the surface treatment of aerated concrete, a chemically resistant, water-repellent layer 3–3.5 cm thick is formed, which reliably protects the material from the penetration of water and chemicals. The results of the performed experiments give reason to believe that on the surface of the pores of aerated concrete treated with a solution based on calcium polysulfide, as well as on the surface of the pores of previously investigated materials, a nanosized coating is formed of sulfur particles that hydrophobic aerated concrete. Conclusions. Comparison of the results for aerated concrete with excellent data for concrete, brick, shell rock shows that the efficiency for aerated concrete is no less and allows us to recommend the specified solution for long-term protection of the surface of aerated concrete walls.

358-364

Authors: Mazitova A.K., Bulatasov Zh.F., Zaripov I.I., Sapozhnikov Yu.E., Vikhareva I.N.

Introduction. The economic activity of a person entails environmental, economic and social damage to the environment. The production of goods or services is associated with the consumption of natural resources and emissions that negatively affect the ecological state. Currently, there is an acute problem of the negative impact of man on the natural environment and is the main source of deterioration in the health of living beings. In modern conditions, chemical safety is one of the priority tasks of socio-economic development. To protect the environment, it is important to take appropriate measures and develop appropriate mechanisms to promote sustainable development. For this purpose, an assessment of the environmental and economic damage from human activities is required. Materials and methods. The work employs the method for determining the prevented environmental damage, approved by the Chairman of the State Committee of the Russian Federation for Environmental Protection, to perform ecological and economic assessment of the environmental impact of new environmentally friendly biodegradable additives for polyvinyl chloride based on adipic acid. Results and discussion. Polymeric materials, as the most popular and widespread, make a significant contribution to the deterioration of the environmental situation. In this regard, the main values of the prevented environmental damage from soil degradation were calculated when using new environmentally friendly additives for PVC based on adipic acid. Conclusion. The introduction of the developed additives into the composition of the developed additives provides economic and environmental efficiency in order to accelerate the biodegradation of polymer composite materials, protects against chemical pollution by hazardous toxic compounds and helps prevent soil degradation.

379-385

Authors: Aminova G.K., Maskova A.R., Yarmukhametova G.U., Gareeva N.B., Mazitova A.K.

Introduction. The increase in production volumes and the expansion of the scope of application of polyvinyl chloride (PVC) compounds contributes to the development of new additives and the attraction of new sources of raw materials for their production. The most important additives necessary for processing PVC are plasticizers. Plasticizers market is one of the largest segments of the global additives market. Since plasticizers are the most simple, cheap and affordable way to modify various properties of the polymeric compositions, their role in processing polymeric materials has recently increased significantly. In application the ester plasticizers, capable to plasticize almost all polymers, especially polyvinylchloride are considered as the most practical. Currently, the industry has mastered production of more than three hundred brands of plasticizers, most of which are esters of phthalic acid. Traditional phthalate plasticizers are the most widely used all over the world. Materials and methods. The paper describes the esterification reactions of phthalic anhydride with oxyethylated (degree of oxyethylation 1.2) and oxypropylated (degree of oxypropelation 1.1) cresols. New symmetric and asymmetric phthalate plasticizers were obtained – dikresoxycresylphthalate, butoxyethylcreoxyethylphthalate, cresylcresoxyethylphthalate and cresylcresoxypropylphthalate, optimum conditions for their preparationare picked up, studied their physical and chemical properties. The obtained experimental data were used to identify promising new phthalate-type plasticizers by the method of cluster analysis. Cluster analysis is the most effective method for solving this problem, because it is intended for combining some samples into classes (clusters) in such a way that the most similar in properties fall into one cluster, but at the same time the samples of different clusters differ as much as possible from each other. Clustering was carried out using the Statistica 10 program. Since at present the reference plasticizer is dioctylphthalate (DOP), the test results of the samples were compared with those of PVC compositions containing DOP. Results and discussions. According to the data obtained, it was found that butoxyethylcreoxyethyl phthalate has the best characteristics in terms of plasticizing ability. The influence of the selected plasticizer on the technological characteristics of PVC-compounds has been studied. The efficiency of the synthesized butoxyethylcreoxyethylphthalate in the PVC composition was evaluated by the indicator (index) of melt flow rate (MFR) and by the indicators of “thermal stability” and “color stability”. Conclusion. Use of the developed additive contributes to the production of PVC compounds with improved rheological characteristics, increased heat resistance and color stability.