Nanotechnologies in Construction: A Scientific Internet-Journal

397-407

Authors: Samchenko S.V., Kozlova I.V., Zemskova O.V., Dudareva M.O.

ABSTRACT: Introduction. The evolution of the construction industry in its current stage calls for the alteration of traditional building materials through the incorporation of nano- and fine-dispersed additives. These additions confer new, unique attributes to cement-based construction materials, enabling control over structure formation processes. Consequently, this allows for the creation of materials with specifically defined characteristics. Additives can be introduced into the cement composite during the joint grinding with clinker minerals, as a component of dry building mixture, or in the form of a suspension instead of mixing water. Therefore, it is essential to obtain fine particles suspensions resistant to aggregation and sedimentation. Thus, the purpose of this study is to obtain stabilized suspensions of bismuth titanate fine particles for cement systems and to study the properties of modified cement stone. Materials and methods. The purpose of this work was to establish the optimal concentration of polycarboxylate plasticizer in industrial water, necessary for the stabilization of fine bismuth titanate suspensions using surface tension and conductometric determination methods, the sedimentation stability of the obtained suspensions and the effect of ultrasonic exposure, as well as the physical and mechanical characteristics of cement stone modified with the obtained suspensions. Results and discussion. In order to establish the optimal concentration of the plasticizer necessary to obtain stable suspensions of bismuth titanate particles, the critical micelle concentration (CMC) for the plasticizer was determined with tap water as the dispersed medium. The CMC value was 1.3 g/l. If the concentration exceeds CMC, the process of micelle formation begins. In the micellar form, the plasticizer no longer provides stabilizing effect on the additive particles, therefore, the concentration of the plasticizer should be lower than the CMC. It was also found that ultrasound exposure increases the sedimentation stability of suspensions. The resulting stabilized suspensions were used instead of mixing water to obtain modified cement stone samples. There is an increase in the compressive strength of cement stone samples obtained after the introduction of fine bismuth titanate into the cement composite in the form of water suspensions stabilized by ultrasonic treatment with concentrations of 10, 30 and 50 g/l. The increase in compressive strength of modified samples compared to reference sample was from 24 to 33 MPa at first day age (by 13, 25 and 38% respectively), and from 80 to 93 MPa at 28 days age (by 4, 9 and 16%). Compressive strength of samples modified with bismuth titanate suspensions after ultrasonication compared to reference sample with plasticizer increased mostly at the first and third days age: from 29 to 42 MPa (by 31, 38 and 45%) and from 53 to 70 MPa (by 28, 30 and 32%) respectively. Conclusion. As a result of the research carried out in this study, the Critical Micelle Concentration (CMC) of a polycarboxylate plasticizer was determined, optimal for stabilizing fine-dispersed additive of bismuth titanate for cement systems, the effectiveness of ultrasonic treatment to achieve sedimentation stability of the obtained suspensions of the additive was confirmed, an increase in the strength characteristics of modified cement stone samples was established both in the initial hardening periods and at 28 days age. The results allow to consider a cement composite with fine bismuth titanate as a basis for obtaining building materials of new generation

418-423

Authors: Vakhitova R.I., Saracheva D.A., Kiyamov I.K., Sabitov L.S., Oleinik V.Iv.

ANNOTATION: Introduction. This article presents the outcomes of research investigations examining the impact of carbon nanotube additives on the phase composition of cement mortars employed in well cementing operations. The quality of work on cementing and ensuring the impermeability of the casing string is quite important in terms of ecological compliance. Research methods. To solve this problem, heavy concrete was modified with a carbon nanoadditive. For research, a cement stone obtained by normalmoisture curing was chosen. Cement mortar CEM III/A32.5H was mixed with tap water for curing, preliminarily stirring a suspension of carbon nanotubes in water solution, a mixture of a water repellent and a hyperplasticizer. To ensure a homogeneous and highly dispersed structure of this suspension, its constituent components were subjected to preliminary dispersion in an ultrasonic field. Results and their discussion. The optimal ratio of carbon nanotubes in the composition of the cement mortar was determined, which amounted to 0.005% of the mass of cement for single-walled carbon nanotubes and 0.0005% for multilayer ones. The process of influence of the selected modifiers on the hydration products and the phase composition of the cement mortar was studied. An additive of complex action, including single-layer carbon nanotubes, was dispersed into solutions of a mixture of hydrophobic and hydrophilic surfactants, which made it possible to increase the strength of cement mortars up to 55%. Conclusion. In terms of modification, single-walled carbon nanotubes are the most efficient

443-452

Authors: Kopanitsa N.O., Demyanenko О.V., Kulikova А.А., Buryanov А.F., Lukyanova N.A., Soloviev V.G.

ABSTRACT: Introduction. This research work investigates the combined influence of nano-sized silicon dioxide (nano-SiO2 ), carbon nanotubes and surfactants on the structural and technological characteristics of cement compositions. Materials and research methods. The paper reveals the findings of a study on the effects of various dispersion techniques of carbon nanotubes (CNT) in surfactants, such as mechanical dispersion, ultrasonic treatment, and a combined method. It considers the uniformity of CNT distribution within the plasticizer and within the cement system, along with their impacts on the physical and mechanical properties of cement stone and concrete. Differential thermal and electron microscopic analysis of aqueous dispersions of carbon nanotubes and hardened activated nanomodified cement stone was carried out. Results and discussion. It has been experimentally proven that mixing nanotubes in dry cement does not allow them to be evenly distributed throughout the volume of the mixture. When using carbon nanotubes, the maximum effect is achieved when they are introduced into aqueous dispersions of plasticizers. The percentage of plasticizer was 1%, CNT 0,1% per 1 liter of water. The most effective method of dispersing carbon nanotubes in a plasticizer is a combined one. The results obtained were used in the preparation of cement stone and concrete compositions. Conclusion. The results show that complex additives consisting of nano-SiO2 and aqueous dispersions of carbon nanotubes have a positive effect on the physical-mechanical and structural-technological properties of cement stone and concrete. Graphic dependencies are shown indicating the effectiveness of using complex additives in the production of cement composites

465-473

Authors: Pavlenko V.I., Gorodov A.I., Yastrebinsky R.N., Lebedev M.S., Kashibadze V.V.

ABSTRACT: Introduction. Silicon oxide film coatings have unique properties and are widely used in various industries, including construction. This paper presents the results on the preparation of polyalkylhydroxysiloxane liquid film in the presence of nanoscale particles of metallic bismuth. Methods and materials. Laser ablation method of metallic bismuth in aqueous medium was used to obtain bismuth nanoparticles. The surface of the target was treated with a laser beam at the workstation of an ytterbium pulsed fiber laser are discussed. The particle size and electrokinetic properties of colloidal bismuth sols were determined method by dynamic light scattering. After drying, Bi powder was added to polyalkylhydroxysiloxane liquid. Thin films cured under different heat treatment modes are applied to glass substrates by dipping. The resulting films were characterized by SEM, X-ray phase analysis, and FTIR spectroscopy. Results. In this work, the electrokinetic properties of colloidal bismuth sols are discussed. Laser ablation of a bismuth substrate leads to an increase in electrical conductivity and the appearance of a double electric layer in colloidal sols. The effect of the curing temperature on the properties of the coating is shown. It was found that the content of bismuth nanoparticles in the polyalkylhydroxysiloxane coating (3 wt.%) does not lead to the formation of crystalline phases. At the same time, he composition of the film and the mode of heat treatment affect the short-range order of molecular bonds. Increasing the content of bismuth nanoparticles in the coating of more than 10 wt.% leads to the appearance of microcrystalline phases of bismuth silicates in the system. Conclusion. The results obtained in the course of the study supplement the information about the production of bismuth nanoparticles by laser ablation and are of great importance in the practice of creating composite films.

482-493

Authors: Bashirov M.G., Bashirova E.M., Yusupova I.G., Akchurin D.Sh., Yulberdin R.T.

ABSTRACT: Introduction. Approximately 20% of accidents in buildings and structures are associated with the destruction of metal structures. Nanocoatings applied to metal structures significantly improve their operational properties, but at the same time make it difficult to use traditional non-destructive testing methods that require access to the surface of the base metal. The quality of the nanocoating is controlled during its formation. To prevent the destruction of metal structures, it is necessary to identify structural heterogeneities of the base metal in micro- and sub-micron sizes, which arise in areas of increased mechanical stress concentration and transform into macrodefects leading to structural failure. Methods and tools are required to non-destructively identify the stress-strain state and damage of the base metal structure through the layer of nanocoating. Electromagnetic-acoustical (EMA) transformation, is considered promising for solving this problem. Existing EMA tools do not fully utilize the potential of EMA conversion, have insufficient sensitivity and the lack of informativity. Methods and materials. For experimental research, we selected widely used in construction structures steels. Research was conducted on the interrelationship of structural alterations in standard samples of metals and the parameters of the electro-magnetic (EMA) transducer under static and cyclic loads. Results. Load diagrams of metal samples were obtained, with accompanying photographs of microstructure in control points, along with their frequency models derived through spectral analysis of the signal from EMA transducer. Discussion. Changes in the stress-strain state of the metal and accumulation of damage in its structure result in a complex interrelated set of changes in mechanical, acoustic, and electro-physical properties, all of which are reflected in the changes in the parameters of the frequency model. Conclusion. Based on the results of the conducted research, the use of a frequency model has been proposed as an integral parameter for identifying the stress-strain state and damage of metal in the equipment. The use of an artificial neural network for analyzing frequency model parameters simplifies the process of identifying the stress-strain state and damage of metal structures and increases its reliability