Jurnal Penelitian Hasil Hutan

167-177

Authors: I.M. Sulastiningsih, Adi Santoso, & Krisdianto

The objective of the study was to determine the effect of various layer compositions on the properties of 3-layer vertically glued laminated bamboo beam (LBB). Bamboo strips for LBB fabrication were prepared from mature culms (± 4 years old) of andong bamboo (Gigantochloa pseudoarundinacea (Steud.) Widjaja) collected from private gardens in West Java. The strips were pre-treated by soaking them in 7% boron solution for four hours. Three-layer LBBs were manufactured with six different layer compositions, including bamboo combination with wood planks of manii (Maesopsis eminii Engl.) or sengon (Falcataria moluccana (Miq.) Barneby & J.W. Grimes) as the core layer. The LBB was manufactured using Water Based Polymer-Isocyanate (WBPI) adhesive. The glue spread and cold pressing time 2 applied were 250 g/m and one hour, respectively. Results showed that the average density, moisture content, thickness 3 swelling, and width expansion of LBB were 0.65 g/cm; 11.1%; 2.09%; and 1.99%, respectively. No delamination occurred in all samples using WBPI adhesive, which indicates high bonding quality. The average bonding strength and 2 percentage bamboo failure (dry test) of LBB were 61.6 kg/cm and 90%, respectively. The physical and mechanical properties of LBB were significantly affected by the layer composition. The presence of wood laminates as the core layer of LBB and the cross wide orientation of the core layer decreased mechanical properties of LBB. On the contrary, the presence of cross-layer in LBB structure increased dimensional stability of the produced LBB.Three-layer thick laminated bamboo beam made of vertically glued andong bamboo strips with various constituted layer composition and all constitued layers laminated together in parallel grain direction had strength values comparable to those of class II of solid wood strength, eventhough the core layer was made of sengon or manii planks.

189-197

Authors: Lisna Efiyanti & Darma Santi

Bioenergy is new and renewable alternative energy which is currently developed enthusiastically. Bioenergy could be produced by catalytic cracking method, which is cracking carbon chain to raise energy fraction. This paper observes potential non-food bioenergy of cashew nut shell liquid as an alternative bioenergy source using catalytic cracking method. The effect of impregnated-metals Nikel and Molibdenum catalyst used in hydrocracking of Cashew Nut Shell Liquid (CNSL) into bioenergy was investigated. It focused specifically on two type of natural activated zeolite catalysts: NiO and NiOMoO at o temperature reaction of 450C and ratio feed catalyst of 2 and 4. Catalysts characterization was conducted according to a gravimetric method to determine acidity of catalyst; Spectroscopy FT-IR analysis to get distribution of active site catalyst; X-Ray Diffraction (XRD) analysis to observe crystalinity of catalyst; and Gas Sorption Analyzer (GSA) to measure surface area, porosity and total of pore volume. Bioenergy of CNSL in the liquid-phase, which were predominantly by gasoline, diesel oil, and heavy oil, was further analyzed using Gas Chromatography-Mass Spectrometry (GC-MS) to determine the compound energy fraction qualitatively and quantitatively. The result showed that the NiOMoO (natural activated zeolite) provided an optimal performance with liquid product conversion was about 65-75%, and selectivity gasoline as well as diesel fraction was about 37-47% and 22-31%, respectively.

207-216

Authors: Ganis Lukmandaru

Beside for its high natural durability and resistancy of weather properties, teak (Tectona grandis) wood is also valued for its beautiful grain and colour. Theoretically, wood colour is highly affected by extractive content, particularly in the heartwood. Identification of correlation between wood colour and extractive content was determined through wood colour and extractive measurements on the outer part of heartwood zone. The wood samples were collected from two locations of Perum Perhutani forest plantations, i.e. KPH Randublatung (35 trees, age class III-IV) and KPH Purwakarta (32 trees, age class VI). Samples were cut from bottom part of the trees and then ground into powder measuring of 40-60 mesh. The wood colour properties(CIE-L*a*b, CIE-L*C*h, CIE-X*Y*Z, Munsell Colour Chart and ISO Brightness) were then measured. Solubility of the teak wood extractives were determined by extracting the powder in ethanol-benzene and hot water respectively. Results showed that the range of colour properties were L*= 40-62; a* = 30 11; b* = 19-31; C* = 20-31; h= 70-82; X= 10-25; Y= 8-23; Z=4-13; H=5-8; V =3-8; C =3-6; and W (ISO Brightness) = 4-12. Different sample location resulted in different trends of correlation between colour properties and extractive contents. No significant correlation was found between extractive solubles in hot water and colour parameters. In general, the best correlations were encountered between brightness parameters from CIE-L*a*b* or ISO with ethanolbenzene extractive contents (r=- 0.54 or 0.50, respectively).

231-239

Authors: Yeni Aprianis, Denny Irawati & Sri Nugroho Marsoem 1 2 2

Terentang wood (Campnosperma auriculata Hook.f) is relatively low in specific gravity (0.3), hence its utilization as pulp by chemi-mechanical is an alternative process. Energy consumption was reduced by applying lignin degrading fungi (Phanerochaete chrysosporium) as pretreatment in the chemi-mechanical process. This paper examines the effects of P. chrysosporium incubation periods into chemical components and energy refining consumption of terentang wood. Four percent of NaOH was used in the chemi-mechanical process, and incubation periods studied were 0 (control), 3, 4 and 5 weeks. Results showed that P. chrysosporium significantly affected the weight loss, chemical properties, and refining energy consumption of terentang wood pulping process. Wood chip weight loss was about 15.9521.31% and alpha-cellulose raised up to 6.77%. Five weeks incubation time decreased lignin content up to 22.97% and saved the refining energy up to 22.7%.