Scientific Journal of Silesian University of Technology. Series Transport

10

Authors: Aftandil MAMMADOV

Typically, an inertial navigation system (INS) is used to determine the position, speed, and orientation of an object moving relative to the earth's surface. The navigation information (position, speed and orientation) of an unmanned aerial vehicle (UAV) is needed to control its flight. Since the resistance of INS to interferences is very high, it is possible to ensure reliable flights in conditions of high-intensity noise. This article explores the principles of constructing inertial measurement units (IMU) that are part of the INS and indicates perspective directions for their development. Micro-electromechanical inertial measurement units were studied in this work, and functional and principal electrical circuits for connecting units of inertial measurements to the microcontroller were developed. The results of practical measurements of units without calibration and after calibration were obtained using the created laboratory device. Based on the obtained results, the necessity of sensor calibration was revealed, and accuracy was improved by performing calibration with the Kalman filter algorithm. The Kalman filter is the heart of the navigation system. In a low-cost system, IMU errors like bias, scale factor error and random walk noise dominate the INS error growth.

11

Authors: Peter KAŠŠAY, Matej URBANSKÝ

Flexible couplings are widely used in mechanical drives of transport and other machines. A fundamental function of flexible shaft couplings regarding torsional vibration is the optimum tuning of torsional oscillating mechanical systems. At the authors’ workplace, the focus is on the research and design of pneumatic couplings, where the torque is transmitted mainly by compressed gas (air) in their pneumatic flexible elements. The primary advantage of these couplings is that their mechanical properties can be quickly and effectively adjusted, especially the dynamic torsional stiffness, by air pressure change directly while the mechanical system is running. This allows us “to tune” the properties of the pneumatic coupling according to the current parameters of the machine drive to avoid resonance and minimize torsional vibration. Therefore, we tend to refer to them as “pneumatic tuners of torsional vibration”. This paper aims to present two new types of these “pneumatic tuners” that were recently granted patent protections, namely “Pneumatic flexible shaft coupling with hose flexible element” and “Drum pneumatic flexible shaft coupling”. Because these pneumatic tuners are not in practical use yet, this paper describes only their design and supposed benefits.

11

Authors: Oleksiy MELNYK, Svitlana ONYSHCHENKO, Oleg ONISHCHENKO, Oleh LOHINOV, Valentyna OCHERETNA, Yurii DOVIDENKO

Widespread use of innovative technologies in all spheres of life has brought the maritime transport industry, in particular, the process of ship navigation, to a completely new qualitative level. Various navigation systems recently introduced and used only as additional devices have gradually become an obligatory element of shipboard equipment and navigation complexes of modern vessels, extending their functionality and capabilities. The human factor influence caused by automation of ship operation processes becomes a separate challenge. Risks to shipping safety and consequences of breach of safety standards for crew, vessel and cargo are far from being a full list of the problems to be solved. This paper offers an overview of general issues of ensuring the level of safety of shipping, by examining the concept of "vessel safety", considering its individual sides, features, as well as constituent aspects of the concept, systematization of the vessel safety structure to develop solutions toward improving the integral safety and optimization of decision-making in emergencies. Achievement of the general purpose of shipping safety thus means the realization of ways of reducing the influence of the human factor on several accidents and an estimation of the degree of influence of a set of factors on a ship during operation.

12

Authors: Adrian GILL, Piotr SMOCZYŃSKI, Damian ŁAWNICZAK

In some areas of transportation systems, reduction of risk using typical safety engineering tools can be difficult due to the relatively small number of events that can be analysed to draw conclusions for the future. One way out of this situation is to analyse systems in their normal operation when no adverse event occurs. It can be done, inter alia, with the Functional Resonance Analysis Method. An important research problem in this context is how to describe the variability of system functions. In this article, we propose an original method, based on the number of hazard sources present in a given analysis domain and apply it to a real pedestrian crossing. The obtained results indicate that the quantitative coincidence measures proposed by us are a convenient way to capture ‘functional vibrations’ in real socio-technical systems. This allows the prediction of undesired states of such systems based on their normal operation.

13

Authors: Sachin SOLANKI, Sanu MEENA, Umesh KUMAR

The Travel Satisfaction Scale (TSS) was created to gauge public opinion on Delhi Metro travel. It has two affective dimensions and one cognitive dimension. This study leverages data from the Delhi Metro commuter trips to undertake new tests because there has been little research on its reliability and structure in the past. Differences in the TSS's reliability and structure – notably for the Delhi Metro and the demographics of the region – are also considered. Finally, the outcomes of this study imply that a single dimension of the affective dimension, rather than the two sub-dimensions, provides a better fit for the Delhi Metro, as well as other public transportation infrastructures in developing countries like India. Individual objects do not load on the two emotional dimensions as intended in a three-dimensional structure, which is more suited for public transportation. Two of the scale's elements – enthusiastic/bored and relaxed/hurried – were associated with the other items in a previous study differing from ours. Researchers should adapt the structure of the TSS in the future by adding or replacing some items with alternate options, which will make it easier to collect data and reduce the burden on the respondent, as well as increase the reliability of the data while maintaining the TSS's consistency and balance.

14

Authors: Marianna TOMAŠKOVÁ, Michaela BALÁŽIKOVÁ, Jozef KRAJŇÁK

Today, being a member of the Fire-Rescue Department (FRD) is challenging as it is a risky and professionally demanding job, which often requires an individual schedule both in terms of physical condition and psychological knowledge as well as safety and health protection at work. Apart from the standard services provided by the FRD and the integrated rescue system, their members also participated in hundreds of interventions during emergencies and crisis situations to mitigate the impacts of the pandemic on society.

17

Authors: Oluwayemi-Oniya ADERIBIGBE, Trynos GUMBO

There is evidence that rural areas are disadvantaged in mobility compared to urban areas. Hence, this study examined spatial variation in the travel pattern of households in urban and rural areas of Nigeria. This study used primary data obtained through questionnaire administration on household heads in the residential zones of both urban and rural areas studied, using the multi-stage sampling technique. Findings revealed that variations exist for age, education level, income level, and occupation in urban and rural areas, and household's average daily mean trip frequency showed a level of fewer trips being generated in the rural area than those in the urban area. Furthermore, the result of the stepwise multiple regression analysis showed that transport mode, household size, number of workers in the house, and occupation of household head were significant variables influencing trip making in urban areas while age, household size, the income of household head and number of employed people were significant in the rural areas. This study concludes that differences exist in the mobility pattern of urban and rural households, and as such, equal consideration and attention should be given to them in policy formulations.

20

Authors: Tomas BINAR, Simona VASIKOVA, Pavel SAFL

To effectively transport materials through different means of transport, it is essential to have an optimized warehouse logistics first. Thanks to the Industry 4.0 platform, there are several ways to accomplish the delivery of materials from a warehouse through transport by road, rail or air. This paper deals with a primary warehouse problem, which is the fast and accurate search and selection of required items in the stock. For this issue, the use of smart glass technology and its implementation in the logistic processes of warehouses could help. In a particular way, an IRS (Integrated Rescue System) warehouse was selected as an example. The augmented reality (AR) type of glasses was selected. The introductory part of this paper deals with the current situation in the warehouse and logistic processes, where the problem of lack of qualified staff and material supply is prevalent, particularly during different crisis situations, such as pandemics or high employee turnovers. The use of smart glasses is one of the many possible problem-solving variants in this field. Further, a basic description of smart glasses, possible uses and sorting are presented in this paper. For the experiment, it was necessary to choose several different commercially available models of smart glasses. An evaluation was provided by the Simple comparative method, Saaty's method and Linear partial utility function method and the best options were identified. Also, there is an example of smart glasses application for picking a particular component in an IRS warehouse in the last part of this paper.

24

Authors: Leszek MINDUR, Maciej MINDUR

This article shows the development of high-speed rail in the Federal Republic of Germany (FRG), its development stages and the shipping companies dealing with this business activity. Special attention was given to the progress in the technical solutions of the track infrastructure as well as during the build of the rolling stock and engines. The high-speed rail was presented in the context of the general development of the economy and transport in Germany. This article contains a synthetic approach to the effects of the functioning of high-speed rail and its financing, as well as further directions and development prospects. Also, this article is based on thoughts, authors’ own research and factual sources of polish and western literature.

9

Authors: Michal PUŠKÁR, Pavol TARBAJOVSKÝ, Marieta ŠOLTÉSOVÁ

Engine emissions can be reduced by performing suitable modifications to the oil filter. Biomass medium served as the replacement for the standard paper fibres, which are used in common oil filters. The experimental analysis of 4 emission elements showed a moderate increase in the case of 2 emission characteristics, whereby a 10% increase in monoxide was present, and also, an increase of 2.5% of nitrogen oxides was observed. Further, there was a significant reduction of 2 other emission elements, namely the unburned hydrocarbons decreased by 61%, and the amount of particulate matter was reduced by 18%. Measured engine power increased by 1.2% using the modified oil filter, which proves the success of this filter. There was a decrease in oil pressure as well, the value dropped by 0.5 bar during the whole period of the measuring process.

11

Authors: Marek MARCISZ, Rafał MORGA, Eryk REMIORZ, Tomasz KRASOŃ, Bartłomiej MICHALIK, Paweł NALEPKA, Szymon POTEMPA, Kacper SAKS, Gabriel SZECÓWKA

Collecting water samples for laboratory analysis from hard-to-reach surface areas such as post-industrial reservoirs (for example, tailings depositories) or overgrown lakes and ponds poses several difficulties, and it is potentially dangerous for the persons carrying out such activity. This can be improved by the use of unmanned aerial vehicles (UAVs) while ensuring an adequate level of safety and full compliance with the requirements of PN-ISO standards. This article presents the possibility of using the BSP in the option of autonomous (automatic) operation, allowing for the collection of water samples intended for physico-chemical tests, from hard-to-reach surface reservoirs, following the provisions of the relevant PN-ISO standards.

12

Authors: Agnieszka DUDZIAK, Monika STOMA, Grzegorz ZAJĄC

Conducting research on the quality of service and customer satisfaction is currently necessary for the proper and effective functioning of any organization. One of the organizations that have changed in recent years is petrol stations. In this paper, the Customer Satisfaction Index (CSI) is used to measure the quality of services and customer satisfaction. This research was carried out with the use of a proprietary questionnaire in which the respondents assessed the level of service at petrol stations. The obtained results allowed identifying the most important areas for the customers of petrol stations. In addition, the developed quality map indicated areas that should be given special attention, improved and those that are least important to customers. The conducted analyzes indicate that the CSI method used in this study is a tool that enables the assessment of customer satisfaction in a complex organization such as a petrol station.

13

Authors: Fuad DASHDAMIROV, Ulvi JAVADLI, Turan VERDİYEV

With the growth of the population and the expansion of the territory of large cities, certain difficulties arise in meeting the needs of passengers for transportation. This article studied the satisfaction of users with the city's public transport system, especially the bus transport. Thus, a survey was conducted among passengers in Baku to assess their satisfaction with public transport. The survey covered all districts of Baku in general. The study was conducted in October 2021. The questions were aimed at identifying the weight, reasons for preferring the different types of public transport, the level of satisfaction of the population with these types, assessing the quality of services and the lack of urban bus transport. The level of satisfaction of survey participants with the work of public transport by gender and age groups was determined. Subsequently, this study showed that most of the population movements are carried out by bus transport. The analysis revealed factors that reduce the quality of service on bus routes. In addition, it examined the reasons why the population chose the bus transport, the shortcomings of the bus transport, the effectiveness of dedicated bus lanes, and attitudes toward the use of alternative public transport. Summarily, this study was successful in identifying the shortcomings of public transport in the city, improving passenger service to increase passenger satisfaction toward attracting more people to public transport.

13

Authors: Oleg ONISHCHENKO, Volodymyr GOLIKOV, Oleksiy MELNYK, Svitlana ONYSHCHENKO, Kostiantyn OBERTIUR

Every year, the dynamics of implementation of projects aimed at improving the efficiency of energy use is gradually increasing at different levels and in different industries. It has spread in the areas of design, modernization and reconstruction of energy-efficient buildings and structures, design and construction of elements of industrial infrastructure, and technological production processes. Introduction of such projects is a priority for enterprises and companies of various types of economic activity. Thus, the leading industries develop strategies to improve environmental safety and energy efficiency - shipping is no exception, where the process of improving energy efficiency is carried out through various mechanisms, ultimately leading to a reduction in emissions of pollutants, but having a negative impact on the performance of the commercial operation of the ship. Problems of ensuring energy efficiency along with increasing requirements for environmental safety of transport and strengthening the responsibility of shipowners become the focus of research of modern theory and practice of operation of means of maritime transport. The issues of improvement of universal principles of energy efficiency within individual shipping companies and development of tools for economic analysis of energy efficiency of own fleet, search for new ways of forming professional competencies of ship crew members in the field of energy efficiency continue to be topical as well.

15

Authors: Aldona KUŚMIŃSKA-FIJAŁKOWSKA, Zbigniew ŁUKASIK, Jacek KOZYRA

One of the priorities of the EU economy is to create the best possible conditions for the design and implementation of innovative solutions within the scope of energy efficiency. In recent years, there has been quick technological progress in the field of devices having controlled motor drive used for air purification, and from heating plates, which are applied in the eating places, including restaurants and zones for preparing meals in various means of transport. The research conducted by the EU on EcoDesign requirements showed that range hoods at the stage of their use have a considerable potential of saving energy. The introduction of energy efficiency labels to the market has improved the energy efficiency of these devices and accelerated the transformation of the market to implement energy-saving technologies, which according to the experts, may lead to an annual primary energy saving of 27 PJ/year in 2021, which may increase in 2030 to 60 PJ/year. The authors of this publication researched the fluid dynamic efficiency of a selected range hood, showing the necessity of investments in new technologies. Patented original solutions of the range hoods that can be applied, among others, in such means of transport as passenger ships, cargo ships, and submarines having a zone for preparing meals were presented in this article. An environmental aspect in the context of energy consumption was shown during the phase of using the device for air purification, providing many premises and arguments for future constructional solutions for energy management in various branches of transport and more.

16

Authors: Zohra GHAFOURI FARD, Mohammad Mahdi KHABIRI, Pouya AFKHAMI MEYBODI

Today, the increasing development of urbanization and climate change and its resulting issues, including the occurrence of urban floods, is one of the important issues facing city managers. One of these problems that seriously affect lives today is the occurrence of floods and the inundation of urban thoroughfares. Among the problems of floods in urban areas are the disruption of the urban transportation system, reduced transportation safety, inundation of thoroughfares, and consequently, the poor appearance of urban roads. One of the successful strategies in controlling urban runoff is the use of porous pavements in urban thoroughfares. The two capabilities of permeability and evaporation of a porous pavement lead to reduced runoff and a resultant lack of occurrence of inundation of thoroughfares; therefore, accurate measurement of these two parameters is of special importance. This study aims to introduce two devices for measuring the permeability and evaporation of porous asphalt with an innovative method that can measure the permeability and evaporation of asphalt and porous concrete with appropriate accuracy.

19

Authors: Sulaimon Olanrewaju ADEBIYI, Oluwagbenga John AKINRINMADE, Bilqis Bolanle AMOLE

Evaluation of Bus Rapid Transportation (BRT) based on service quality criteria and customer satisfaction can never be overemphasized due to its derivative, such as optimizing the performance of the transportation industry. Thus, this study employs the multi-criteria decision-making (MCDM) method for the evaluation of service quality and customer satisfaction of the BRT system in Nigeria using the fuzzy analytical hierarchy process (FAHP) and visekriterijumska optimizacija i kompromisno resenje (VIKOR), which are components of multi-criteria optimization and compromise solution to evaluate notable factors responsible for the user’s perspective. Research design is quantitative and analytical in nature through a survey of experts who are users of BRT services. Samples were drawn through a multi-stage sampling procedure and a total of 402 copies of questionnaires were administered to BRT users based on their experience with the system. Hence, VIKOR and FAHP methods are applied to analyse data retrieved from the field on services quality and performance level. The service quality (SERVQUAL) model (a multi-dimensional research instrument designed to capture consumer expectations and perceptions of service) was modified thereby generating six dimensions and thirty-six service criteria for this research. The FAHP method was employed to determine the weights of the decision criteria because there is a need to measure commuters’ perceptions and expectations based on numerical linguistic variables due to the vague, imprecise and complexity related to the nature of services. The criteria weights and responses of the survey analysis (data) related with the BRT are input for the VIKOR method for ranking. As measuring the perception of service quality based on crispy value can often be misleading, hence, the use of the fuzzy MCDM method can give a more realistic measurement. The result of the multi-criteria decision analysis revealed that pricing quality is the most relevant service quality dimension to users’ satisfaction, followed by the empathy quality dimension. The summary of strength and weakness areas of service quality discovered through the research and its managerial implications with recommendations were related to the appropriate authority in charge of the BRT system for improved performance.

31

Authors: Zineb ACHETOUI, Charif MABROUKI, Ahmed MOUSRIJ

This paper aims to provide a performance measurement system for the automotive spare parts supply chain. We focus on an independent distributor belonging to an independent channel. The framework encompasses different performance aspects for a high supply chain visibility, as well as the required categories, subcategories and key performance indicators for the automotive spare parts supply chain performance measurement. The framework is the first contribution that advances the performance measurement in the automotive aftermarket and allows assessing the performance of the automotive spare parts supply chain as a whole.

8

Authors: Bożena SZCZUCKA-LASOTA, Tomasz WĘGRZYN

Telecommunication, transport and civil engineering play an important role in new research areas. New antennas based on innovative materials are being developed. At the same time, the methods of antenna mounting with the use of high-strength materials to ensure high structural rigidity with the lowest possible weight are being planned. These materials include AHSS steels with ultimate tensile strength (UTS) up to 1700 MPa and elevated yield point (YS); however, welded joints made of these steels have much worse mechanical properties, compared to the native materials. In this paper, it was planned to test the MAG welding of DOCOL 1400M steel (AHSS group). Directly after welding, a micro-jet joint cooling was applied. It was determined to create thin-walled joints that could be used in the formation of antenna mounts.

10

Authors: Igor Alex VAKULENKO, Leonid VAKULENKO, Dariy BOLOTOVA, Bulent KURT, Hangardash ASGAROV, Ömer ÇÖLOVA

When simulating the operating conditions of the rim of a railway wheel, an analysis of change in the structural state from the possible degree of plastic deformation and the heating temperature of steel near the rolling surface was carried out. The development processes of spheroidization and coalescence of cementite during heating of the cold-worked steel change its ability to strain hardening. Substructure changes during heating to temperatures of 500-550°C deformed steel are accompanied by a simultaneous decrease in its ability to strain hardening and the level of plasticity. When heated above 500-550°C, the development of ferrite recrystallization processes provides a gradual transition of the metal from substructure hardening to hardening from grain boundaries with large angles of disorientation. It is shown that regardless of the nature of the main structural element, the ability of steel to strain hardening and the level of plasticity after heating are related by a proportional relationship.

12

Authors: Elshan MANAFOV, Islam ISGANDAROV, Farid HUSEYNOV

This research was devoted to the creation of a protection system for electric motors used in industry and transport, based on modern and traditional sensors. In the course of operation, the malfunctions of electric motors have been investigated and it was found that the accident modes occur mainly due to exceeding the permissible values of the current, voltage and temperature parameters. Modern sensors of current, voltage, and temperature have been compared and the most effective ones were selected for use in electric motors. Based on reasoning from these sensors, a protection system for a low-power electric motor has been developed in the laboratory. In addition, in the Multisim application software package, a simulation of the operation of the protection system at different voltage and current values was performed, and a circuit of the sensor control unit and the power source for powering the protection system was constructed. It has been proposed to apply such a multi-parametric complex protection system for electric motors, especially in transport.

14

Authors: Evgeny MIKHAILOV, Stanislav SEMENOV, Hanna SHVORNIKOVA, Ján DIŽO, Miroslav BLATNICKÝ, Paweł DROŹDZIEL, Kateryna KRAVCHENKO

This work is focused on the possible ways of improving the running safety of a railway vehicle, which uses IRWs (independently rotating wheels) in a bogie. It discusses the main positive and negative properties of an application of IRWs for a railway vehicle while it is running in a curve. There are evaluated running properties of a railway vehicle in terms of safety for IRWs and a standard wheelset (SW). It is assumed that a wheelset design with IRWs will reduce the risk of derailment of a railway vehicle in a curve with a smaller radius because it will be reached a more favourable distribution of decisive forces in the wheel/rail contact. A designed wheelset with IRWs differs from other IRWs designs; in this case, only a flange can rotate independently from a wheel treat surface about the axis of rotation. Further, this research presents an analysis of a friction forces distribution of the friction forces in a contact of a flange and a rail head and a comparison with an SW. The obtained results allow concluding that it is advisable to use the wheels with the perspective wheel design (including independently rotating) to reduce the resistance to movement and improve the running properties of a railway vehicle for safety.

14

Authors: Yağmur ÖZİNAL AVŞAR, Ercan AVŞAR

Estimation of the state of road traffic conditions is gaining increasing attention in recent intelligent transportation systems. Accurate and real-time estimation of traffic condition changes is critical in the management and control of road network systems. Thus, efforts are been made to predict short-term traffic conditions based on measured traffic data such as speed, flow and density. In this work, the state of the traffic is estimated through a three-step process. First, both speed and flow predictions for 15-minute ahead are made for a particular freeway segment. Four different regression models are used for the prediction task, namely, multi-layer perceptron neural networks (MLPNN), support vector regression (SVR), gradient boosted decision trees (GBDT), and k-nearest neighbors (kNN). Next, the breakpoint (BP) flow is calculated using the distribution of these predicted speed and flow values. In the final step, these predictions are classified as belonging to a “stable state” or “metastable state” by using the calculated BP as the threshold between these states. According to the experimental results, the values for MLPNN are the highest for speed (0.8564) and flow (0.9862) predictions. An identical BP, 1050 pc/15min, is calculated for actual data as well as all prediction methods.

16

Authors: Sandeep YADAV, Amit KUMAR, Abhilasha CHAUDHAR

Extensive research is being conducted to create and use a wide range of alternative fuels to accommodate the world's growing energy needs. The objective of this experimental investigation was to analyze the effects of Karanja biodiesel blends on the performance, combustion, and emission characteristics of a compression ignition (CI) engine vis-a-vis neat diesel. Important physical parameters of Karanja oil were examined experimentally after transesterification and determined to be within acceptable limits. BTE of Karanja biodiesel blends was about 3-8% lower than diesel. For Karanja biodiesel blends, BSFC was about 2-9% higher than diesel but exhaust gas temperature and volumetric efficiency were lower. Emissions characteristics such as nitrogen oxides, hydrocarbons, and carbon monoxide were also analyzed for various tested fuels. Karanja biodiesel blends resulted in lesser CO and HC formation. Nonetheless, NOx emissions were around 10% greater than diesel. Peak cylinder pressure, heat release rate, and maximum rate of pressure rise versus crank angle were among the combustion characteristics parameters considered in this study. Combustion analysis revealed that for Karanja biodiesel blends heat release rate and peak cylinder pressure were lower than for neat diesel. Findings indicate that Karanja biodiesel can be considered a viable diesel engine fuel.

17

Authors: Zbigniew ŁUKASIK, Aldona KUŚMIŃSKA-FIJAŁKOWSKA, Sylwia OLSZAŃSKA, Mateusz ROMAN

Today, route planning requires freight forwarders to make a conscious effort to identify unloading points such that the transport process is both cost- and time-efficient. At the same time, operational parameters that help to determine the validity of the chosen route must also be considered. This article aims to present the key metrics and ways of attaining them to provide a reliable determination of a transport company’s performance. Based on a selected transport company, the authors collected data on the transport routes implemented in 2020. Interpretation and analysis of the extracted information of the concerned sections were carried out and followed by alternatives. We present in this article the results of research concerning the exploitation parameters of the vehicle set. The evaluation of a given route section was indicated using selected indicators adapted to the specificity of the enterprise. The results are aimed at locating the components that have a destructive impact on the entire process. The proposed solutions serve to introduce factors that will pave way for improving the services provided. An in-depth analysis of all sections and key parameters was performed. Because of the conducted studies, abnormal parameters were identified, efficient sections were distinguished and new routes were developed in the case of previous routes that were not highly efficient and which had a possible alternative corridor. The obtained results of the research can comprise, for logistics managers, vital elements in the transport process, to which attention should be given in the course of overseeing these processes.

18

Authors: Jan WARCZEK, Rafał WÓJAK

Increasing exports of goods between countries over long distances and increasing amounts of cargo generated by ports and transported on roads and railways require the organization of cargo transportation using several modes of transport, forcing the construction of places (container terminals) where it is possible to reload them to other means of transportation. An important aspect of cargo transportation by intermodal transport is its proper securing with the use of properly selected packaging and a loading unit. This article shows how to properly prepare cargo for transport. It also presents a diagram of the correct calculations of the permissible masses that may be in the container during transport to prevent overloading of the container and evenly distribute the load so that the reloading devices located in container terminals are not damaged during reloading to another mode of transport. Therefore, appropriate securing of the load against its displacement and damage was also selected.

25

Authors: Lidiia SAVCHENKO, Mariya GRYGORAK, Volodymyr POLISHCHUK, Yuriy VOVK, Oleg LYASHUK, Iryna VOVK, Roman KHUDOBEI

A methodical approach for the determination of economic and socio-environmental costs in the application of the city consolidation center at the micro level was proposed and tested on real data. Two options of urban delivery of small shipments are considered, in particular, for e-commerce - direct delivery and delivery through the micro-consolidation center. The system of indicators proposed in this work allows a detailed assessment of the economic component of direct and consolidated delivery, including transportation costs, the functioning of the consolidation center costs and costs for pedestrian delivery to the residential district customers. Socio-economic indicators allow considering the interests of other residents of the city, suffering from a dense traffic flow and harmful emissions from freight vehicles. The proposed method of integrated assessment was tested on real data of a micro district of the city. The results made it possible to estimate the proportion of each component of expenditures in the economic, socio-environmental and total costs for both delivery options. The analysis of the sensitivity of costs to changes in the input parameters showed the difference in the strength of influence, and the rating of influencing factors. The proposed method allows us to estimate the economic costs of all participants in the urban delivery process for small shipments, as well as to prove the rationality of using micro-consolidation to serve a micro district of a large city.

9

Authors: Blerina BEQAJ

Water is one of nature’s resources. As urbanisation grows, new roadways and highways are constructed for the transport sector and development. Due to roadway infrastructure, the development of the quality of surface water bodies in close proximity to roads is deteriorating and has become a major environmental challenge. Considered as one of the major nonpoint pollution sources, the construction of new roadways can have short and long-term effects on water quality conditions. This study revealed that road construction activities may be responsible for introducing pollutants in nearby water sources, leading to the deterioration of water quality. The roadway expansion activities affect both the surface and groundwater quality. Furthermore, this study was conducted to assess the effects of a road construction project situated in the southern part of Albania, on physic-chemical parameters of surface water by collecting water samples from Skotini stream. The analysed parameters included pH, dissolved oxygen (DO), biological oxygen demand (BOD5), chemical oxygen demand (COD), electrical conductivity (ECw), total dissolved solids (TDS), salinity, nitrites (NO2-), ammonium (NH4+) and total phosphorus (Ptot). The results revealed that all physic-chemical parameters analysed in the laboratory are between the normal standards classifying these waters as very clean. Further surveillance for quality assessment of water sources near roadway’s construction activities is needed. Various best management practices have been developed and implemented to prevent negative environmental impacts in the transport sector and roadway construction activities. Results of the water quality help strengthen the theory that roadway construction projects in the transport sector, using appropriate best management practices, could yield minimal impact on the overall water quality of surrounding water bodies.

11

Authors: Agata KUREK, Elżbieta MACIOSZEK

Currently, more inhabitants use a car for their travels. The consequence of the increase in traffic on the roads is the deterioration of road conditions, decrease in the level of road safety, increasing air pollution, as well as the problem of finding a place to park a vehicle. This article analyzes the daily variability of the use of parking spaces in the Paid Parking Zone (PPZ) covered by Dynamic Parking Information (DPI) in Gliwice before and during the COVID-19 pandemic. In the first stage of the work, the daily variability of the use of parking spaces and the rotation indicator were analyzed in parking spaces at PPZ covered by DPI before and during the COVID-19 pandemic. The Wilcoxon test was performed to verify whether the differences are statistically significant. The results indicate that the COVID-19 pandemic contributed to the decrease in the use of parking space and the rotation indicator in the parking spaces at PPZ. In addition, the research shows that collecting fees for parking a vehicle in a parking space increases the use of space and the rotation indicator. Due to this, parking spaces are available for more drivers.

11

Authors: Oleksiy MELNYK, Yuriy BYCHKOVSKY, Andrii VOLOSHYN

The maritime industry is a high-risk industry, which constantly has to make decisions in a rapidly changing environment. Therefore, understanding the essence of "situational awareness" is very important for making the right decision. In this regard, it is obvious that a correct situation analysis, based on a theoretical basis, creates the proper prerequisites for making the right decision in a developing situation, and vice versa. Considering this fact, this article proposes to study the factors that influence this phenomenon, their regularities and connections. It presents the data of a survey among seafarers to determine the level of understanding of situational awareness as a predominant component of the human factor in most accidents in the maritime industry.

12

Authors: Radka JÍROVÁ, Lubomír PEŠÍK

Air conditioning systems in vehicles require long-term reliability during their entire service life. Especially, a good sealing function is needed for the prevention of coolant leaking. Unfortunately, in specific cases, after a particular time, screw connections of the air conditioning circuit lose their tightness, and the coolant starts to leak. Therefore, this paper focuses on the analysis and design optimisation of screw connections. We used the finite element method for describing the sealing, screw and disc spring behaviour. Then, we proposed a new design of the disc spring to obtain the proper force-deformation characteristics of the connection and ensure the tightness of the screw connection.

12

Authors: Vladimir NEKHOROSHKOV, Sergey VAKULENKO, Peter KURENKOV, Evgeniy NEKHOROSHKOV, Grigoriy DERUZHINSKIY, Alexander IGNATENKO, Alyona AROSHIDZE, Alexey ASTAFIEV, Irina SERYAPOVA, Irina SOLSKAYA

The development of international cargo transportation has been relevant since the emergence of the international division of labor. Billions of tons of goods of various names, values and volumes are transported across the borders of the Russian Federation every year. This paper examines the Eurasian Economic Union international transportation system, its transport system integration, and the formation of a common transport space. The authors analyzed the international transport market state and conditions and the level of containerization. The transport system is considered the country's economy "circulatory system", which makes it a key link in the implementation of economic reforms in the country. The transport industry has social significance, which also determines the specifics of the phased market transformations. The development of international multimodal container transportation is becoming a new trend in the development of the transport service market.

12

Authors: Kanala Teja Vinay Kumar REDDY, Surya Prakash CHALLAGULLA

Unexpected delay on freeways is the prime cause of dissatisfaction in road users. Increasing traffic, adverse environmental conditions, accidents, time, season, location and many more factors influence travel time and cause delay. There is no direct method to estimate delay. It is calculated from trip time estimates. Thus, it is a very big challenge for transportation professionals to develop a model that accurately estimates the trip time for a trip at a particular time, by a specific mode of transport. Subsequently, the reliability of the delay calculated from those trip time estimates is often doubtful. Further, the measurement of delay using the trip time data is another big thing. This paper is a step toward measuring the delay in an accurate way using travel time reliability measures. The study was conducted on the two modes of public transportation (City bus and Auto) in an urban corridor of length 16.3 km, in Hyderabad city, India. In this study, a license plate survey was conducted for data collection, travel time-based statistical analysis was employed for estimation of trip time and by making use of travel time measures, the delay was measured. The approach was validated graphically to portray its accuracy.

14

Authors: Greg WHEATLEY, Arash BABAMIRI, Bronson PHILIPPA

Airlie beach houses are quite common in the coastal areas of Australia. These houses, similar to other buildings, provide comfort for their residents. House comfort is not limited to temperature or sound pollution, vibration can be considered as another equally important factor. In this article, the vibration of an Airlie beach house was investigated. The base steel structure was modeled in SolidWorks and Space Gass for evaluating stress distribution and nodal displacement, respectively. To find the root cause of the distressing vibration of the house, which was felt with dwellings, the axial acceleration of the house’s structure was determined. Some feasible solutions such as adding a fiber-reinforced polymer joist hanger, inserting additional rubber padding to the joist hanger, and attaching additional bracing, were discussed and a cost analysis was considered for the solutions. Eventually, the nature of the best solution, which was adding rubber, was tested experimentally.

16

Authors: Mulugeta GIRMA, Berhanu WOLDETENSAE

Rapid urbanization has resulted in a slew of issues, including urban transportation, in most emerging countries' cities. Public transportation provides transportation for the community and plays an important role in the daily lives of the city's citizens, particularly the urban poor, by reducing travel costs and providing job opportunities. Thus, evaluating public bus service performance from the perspective of users is critical for identifying service operators' strengths and deficiencies. Consequently, the primary goal of this research is to determine the level of consumer satisfaction with public bus service in the city and identify the most important factors that influence satisfaction. Hence, a survey was carried out between December and January 2020. Stratified sampling approaches were used to obtain data from 500 travelers. Factor analysis and customer satisfaction index were used to analyze the data collected. Lastly, the findings show that users were quietly satisfied (0.54) with the quality of the bus services supplied in the city. Moreover, travelers were better satisfied with attributes that related to availability (0.64) and less satisfied with attributes under timeliness (0.50) and security (0.48). Therefore, service operators and other concerned stakeholders should give urgent attention to attributes under timeliness and security to enhance users’ satisfaction in the provision of bus service in the city.

17

Authors: Michał ZIĘTALA

This paper presents the stability of the GPS and GLONASS system clocks’ stability. It describes the construction of these two systems and calculated four different Allan variances (AVAR), based on the MGEX (the Multi-GNSS Experiment) clock products. Four used variances allowed making a better analysis of each GNSS system clock. The results are shown at different averaging times from 5 s as successive multiples to 655,360 s in a monthly period. The stability of GPS and GLONASS clocks is included in the range of 10-12~10-14 s. The results showed that GLONASS clocks are stable (10-12~10-14 s) and are affected with white frequency noise (WFM). The GPS clock stability models have more fluctuations for τ > 40,960 s and the mean stability is concluded between 10-12~10-13 s. Mean frequency accuracy for GPS clocks is related with WFM and Random Walk Frequency (RWF). The differences in clock stability are caused by several factors – block type, type of clock and the time of a satellite in orbit. These factors have an influence on stability results.