Mehran University Research Journal of Engineering and Technology

8

Authors: Farooq Azam; Shahid Bashir; Muhammad Ammar Sohaib

5G (Fifth Generation) is the next generation of data network, offering faster speeds and reliable connections on smart phones and other devices than ever before. These networks are still under development and expected to operate on 28 and 38GHz bands. However, multiple antennas required for these 5G devices will increase the overall system size. Single antenna which can switch to operate on multiple bands is the solution to this problem. A novel frequency reconfigurable antenna for 5G communication networks is presented in this paper. The antenna was designed on a Roger R5880 substrate having dielectric constant 2.2 and loss tangent 0.0009. The proposed antenna consists of simple radiator on top layer and two slots in the ground layer. The frequency re-configurability is achieved by placing three PIN diodes in each slot of the ground. The operating frequency band of antenna is controlled by switching states of PIN diodes. The proposed antenna covers a wide band from 25.6-39.3 GHz by simply switching the diodes ON/OFF. Thus it can cover 28 and 38 GHz bands that are anticipated to be the two working bands for 5G communication. The overall size of the antenna is 10x7 mm2. In addition to being small this antenna has a good gain ranging from 6.5-8.4 dB as well as 85% efficiency in the two 5G bands. All simulations have been done in CST (Computer Simulation Technology) Studio Suite. This reconfigurable antenna can find applications in future 5G communication networks.

8

Authors: Sallahuddin Panhwar; Abdul Razaque Sahito; Ghulam Shabir Solangi; Rasool Bux Mahar; Jawahar Lal

DSW (Distillery Spent Wash) is superfluous residual liquid waste produced during the process of alcohol production. It is one of the most critical environmental issues which cause pollution. Despite strictness of standards imposed on effluent quality, partially or untreated effluent very often finds access to surface and groundwater. The distillery wastewater becomes a serious risk to the water quality in several regions around the globe. The ever-increasing generation of DSW lead to take an attempt to investigate a few aspects of anaerobic digestion of spent wash collected from a distillery. In the present study CSTR (Continuous Stirred Tank Reactor) was used at laboratory scale. The study was carried out to evaluate the performance of CSTR after the effective startup and the gradual increment in the OLR (Organic Loading Rate). The maximum methane gas (CH4) of 71.68 ml at the OLR of 1.0g of COD (Chemical Oxygen Demand)/L was observed. The optimum COD removal efficiency of the CSTR was 91% corresponding to OLR of 1g of COD/L. The pH ranges from 7.1-7.3 gave better performance and maximum stability of the process. By increasing the ORL, the VFA (Volatile Fatty Acids) content was also increased and reached to the 1.5g COD/L. However, the removal efficiency of TS (Total Solids) increased at an accelerated rate of OLR.

10

Authors: Mushtaq M.I.; Siddiq A.; Tariq M.O.;, Ali A.; Zahra A.

Energy management in home is one of the major issue now-a-days. There are different types of load like shiftable, non-shiftable, seasonal loads and auxiliary loads. In this research article, an energy management system is proposed for home which helps to schedule different loads on the basis of their types and price. It will help to minimize the cost of electricity by shifting load from peak time to off peak time. Emission will be minimized by charging penalty by adopting multi-objective optimization. Each source of energy has its own price of penalty with respect to time. Penalty is charged to minimize the use of sources like commercial supply and diesel generators which emits hazardous gases. In proposed model, user will get electricity from commercial supply, diesel generators and solar panels to provide continuous supply of electricity to fulfil the energy demand. The shiftable loads will be shifted from peak time to off peak time and higher price source to lower price source to minimize the overall price. In this research, we have proposed an EEIR (Economically Effective and Intelligently Responsive) HEMS (Home Energy Management System) by solving multi-objective optimization problem from BILP (Binary Integer Linear Programming) using branch and bound algorithm.

10

Authors: Khawaja Adeel Tariq; Muhammad Moeen Soharwardy; Nadeem Ahmed Tabessum

This study deals with the evaluation of soil engineering characteristic along the proposed route of Jalalpur irrigation project. The proposed JIP (Jalalpur Irrigation Project) is located along the right bank of Jhelum River in Tehsil PDK (Pind Dadan Khan) and Tehsil Khushab of District Khushab. JIP is funded by ADB (Asian Development Bank). The JIP will enhance crop production in Tehsil PDK and Khushab. Famers will be benefited through JIP as they will get regular supply of water through canal. It will also create job opportunities for local people and will lead to the prosperity of the Project area.Detailed soil investigation along proposed route was carried out by M/S GEOBAND. Straight rotary method of drilling was used. The recovered soil samples and water samples were tested in laboratories.The detailed engineering analysis was performed and soil parameters along with bearing capacities are suggested. Results have indicated variations in SPT values along the proposed route. The top layer of soil along proposed route is mostly Silty Clay with variation along the depth. The proposed bearing capacity for shallow foundation is 1.25 ton/ft2 (120 kN/m2) at depth of 5ft (1.5 m) beneath footing, and for bored piles having diameter of 2.5 ft (0.76 m) at a depth of 50 ft (15 m) is recommended as 70 ton (685 kN). The results presented in this study will be helpful in deciding the detailed foundation design of the engineering structures along the proposed route of JIP.

12

Authors: Muhammad Imran; Saeed Badshah; Rafiullah Khan

Composites are one of the rapidly consuming materials due to their utmost attractive applications ranging from the aerospace to the agricultural products. The composite structures usually experience vibration during service. Experiments showed that presence of delamination in composite structures is one of the major causes of failures in laminated structures. Presence of delamination in a structure not only significantly impacts the stiffness of the structure with declining trends but also affect their vibration properties. The purpose of this paper is to review the literature studies on the effect of vibration on composite delaminated structures subjected to different boundary conditions. The literature studies have been classified on the basis of methodology adpated to analyze the problem i.e experimental work, analytical approaches and finite element methods. In this review particular attention has been given to the study of results attained from the analytical analysis, finite element and experimental works. Comparison of the results conducted by other researchers in the field of the free and forced vibration behavior of the composite laminates subjected to delamination or cracked structures has also been studied. Studies have shown that the location and size of delamination in composite structures significantly impacted the natural frequencies and mode shapes.

12

Authors: Abdul Rauf Jamali; Waseem Khan; Ali Dad Chandio; Zubai Anwer; Muhammad Hayat Jokhio

From last epoch till to date, AISI 4340 and AISI 4140 have been widely used in different engineering applications. These applications include bolt, screws, gears, drive shafts, crane shaft and piston rods for engines due to its upright mechanical properties, cost-effective and easily available in market. In present work, deep cryogenic treatment effect on the mechanical properties of AISI 4340 and AISI 4140 have been studied. Present work was carried out at laboratory scale and can be extended for mass production. Our work is simple, straight forward safe and economical. In our work, samples were heat treated in simple muffle furnace and followed by cryogenic treatment in liquid nitrogen. Before cryogenic treatment, all samples were normalized at 860°C to obtain homogenized microstructure. Samples were also compared conventionally heat treatment with quenched in oil quenchant. Experimental results showed that after cryogenic treatment with tempering treatment, one could easily increase the tensile strength, impact toughness and hardness. Advanced optical microscopy (IMM 901) and SEM (Scanning Electron Microscopy), FIT Quanta 200 methods have also been deployed to reveal and interpret the internal structure of samples. It was found from microstructure that cryogenic treated sample increases the impact strength, hardness and tensile strength as compared conventional heat treated quenching approaches.

14

Authors: Muhammad Farhan Khan; Syed Muhammad Ghazanfar Monir; Imran Naseem

Zero-watermarking of digital images is a powerful method with respect to transparency in the watermarked image. However, robustness is still a challenging characteristic for researchers. The proposed method of zero-watermarking provides a novel solution for increasing robustness by obtaining resident features of grayscale image that are robust against common signal processing operations. The proposed solution is based on image scanning to produce NDD (NeighboringDistance Difference) profile. This scheme is used to extract image features for generating redundancy binary profile with the help of image scanning and identification of robust image areas for embedding a binary watermark. Redundant areas from binary profile show perceptually insignificant regions of grayscale image according to human visual system. Resident features from robust areas of image are collected to generate the zerowatermarking binary key image using reversible XOR operation. The binary key is used for extraction of binary watermark. Experimental results of the proposed method have been compared with the results of various zero-watermarking schemes as well as traditional watermarking methods and found much better at slightly higher computational cost. The comparison analysis for testing robustness has been carried out against image processing attacks like Gaussian filtering, block average filtering, motion blur filtering, image resizing, image rotation, image compression and cropping. For each attack maximum correlated watermark from the set of recovered watermarks is selected to evaluate the performance of proposed zero-watermarking scheme. It has been recorded that perfect matching is observed between original and extracted watermarks for a number of signal processing attacks.

16

Authors: Cao W.; Bukhari A.A.S.; Aarniovuori L.

EVs (Electric Vehicles) have been rejuvenated over the last decades while the motor drive technologies are still evolving. This paper provides a review of electrical motor drive technologies used in EV applications, with a performance comparison of candidate machines and their drive topologies. EV applications demand high efficiency, high torque density, high reliability, and wide speed range while reducing weight, complexity, total costs and environmental impact. In the literature, DC (Direct Current) motors, IMs (Induction Motors) and PM (Permanent Magnet) motors can be generally found in marketplace whilst RMs (Reluctance Motors) have been researched for some time and are nearing commercial availability. This paper evaluates the performance of these four main types of electrical motor drives for EV propulsion applications using analytical methods. PM motors may offer the best performance in terms of torque density and compactness but the cost is the highest (primarily dominated by rare-earth permanent magnets), limiting their widespread application in mass production EVs. DC motors have their own merits but suffer from limited power density and necessity for maintenance. Induction motor drives are a mature and proven technology. In particular, squirrel-cage IMs are robust, reliable and inexpensive, striking a balance between system cost and complexity, power density and extended speed range. Reluctance motors can provide a good torque density and cost effective EV drive solutions. Their drawbacks can also be overcome by the use of power electronic converters and advanced control strategies. Induction and reluctance motor drives are well suited for cost sensitive mass production EV applications. Looking to the future, increased hybridization may be a way forward in industry which combines attractive features of different electrical machines and control algorithms and still offer much promise in performance and total cost. At last, reliability study on EVs requires historical information and driving patterns, demanding research expertise in eco-sociology, human behaviors as well as human-machine interface.

16

Authors: Tajwali Khan; Ihtzaz Qamar

Optimum characteristic length of the combustion chamber of liquid rocket engine is very important to get higher energy from the liquid propellants. Characteristic length is defined by the time required for complete burning of fuel. Combustion reactions are very fast and combustion is evaporation dependent. This paper proposes fuel droplet evaporation model for liquid propellant rocket engine and discusses the factors which can affect the required size of characteristic length of the combustion chamber based on proposed model. The analysis is performed for low temperature combustion chamber. A computer code based on proposed model is generated, which solve analytical equations to calculate combustion chamber characteristic length under various input conditions. The analysis shows that characteristic length is affected by combustion chamber temperature, pressure, fuel droplet diameter, chamber diameter, mass flow rate of propellants and relative velocity of the droplet in the combustion chamber.

16

Authors: Tania Ali Soomro; Mohsin Ali Soomro; Hummaira Kanwal

Karachi being the first born city of the colonial architecture in Sindh Pakistan has the honour of housing very important and diverse ornamental architectural master pieces. Along with the commercial nucleus; Karachi emerged as a regional educational hub after the partition of the Indian subcontinent in 1947 with several hostel structures and studio apartments. These structures are among the better examples of the pre-colonial and post-colonial architectural influence in the region. Few of them (still surviving) are incorporated in the national list of protected heritage under Sindh Cultural Heritage Preservation Act 1994. This research paper is focused on “the lost importance of the three different hostel (boys’ hostels only) premises in the historic core of the city of Karachi”. Despite possessing similar functions in the past and having the same status of the declared protected heritage at present, each of them has different use and conservation status at present. None of the buildings have endured the original function. This research focuses the reasons of the non-continuation of the original function and the impairments caused to the buildings due to this reason. Methodology followed for the research includes analysis of available archives, physical observation, photographic documentation and interviews with the local inhabitants of the neighbourhood. The results and the findings of this research portray that eroding hostel culture has subjected those structures to slow and painful death of their original purpose. These buildings, once popular in the area, are now fading fast and perhaps will cease to exist in the near future unless the immediate precautionary measures are taken. The main conclusion drawn in this paper is that “it is important to preserve those historic premises as they are of significant historic character that remained associated with a number of key political and social personalities of the region. Moreover, they play a vital role in the general architectural value of the region”.

16

Authors: Abdul Salam Khan

Sustainable production systems require optimal utilization of resources. Raw material acquisition is one of the costly processes in a production system. EOL (End-of-Life) products re-manufacturing through reverse logistics can help in decreasing excessive raw material cost. In this study, we consider production system of closed loop supply chain in which both forward and reverse production systems are active. DOE (Design of Experiments) methodology is incorporated which is a statistical approach adopted in dealing with complex workplace problems. We employ L9 orthogonal array using Taguchi experiment in Minitab 17 and DOE for plotting the results. Dependent variables used in this study are productivity, P (number of forward and reverse products produced per period) and quality accuracy of product (measured in percent deviation from reference standards). A trade-off analysis between the control variables is presented on the basis of SNR (Signal to Noise Ratio). Control variables used in the analysis are tools employed in production system (tu), number of machines being used (m) and dedicated manufacturing cells (dc). We use three levels of analysis for each control factor. Optimum result conditions are calculated using signal to noise ratio with larger-the-better-criteria as well as smaller-the-better criteria and study is concluded with main effects of the mean plots. DOE optimization analysis for productivity suggests combination set of 32, 8, and 6 for tools, machines in use and manufacturing cells, respectively. Similarly, for optimal dimensional accuracy, tools used are 24; number of machines in use is 14 with 3 manufacturing cells. All result indices are accomplished within a confidence interval of 95% with p-values less than 0.05. MILP (Mixed Integer Linear Programming) analysis considers cost function of production and transportation between tools, machines and levels and Taguchi based experimental findings are validated by mathematical optimization findings.

18

Authors: Nida Saddaf khan; Muhammad Sayeed Ghani

The increasing use of social media offers researchers with an opportunity to apply the sentiment analysis techniques over the data collected from social media websites. These techniques promise to provide an insight into the users’ perspectives on many areas. In this research, a sentiment analysis model is proposed based on HMC (Hidden Markov Chains) and K-Means algorithm to predict the collective synchronous state of sentiments for users on social media. HMC are used to find the converged state while K-Means is used to find the representative group of users. For this purpose, we have used data from a well-known social media site, Twitter, which consists of the tweets about a famous political party in Pakistan. The time series sequences of sentiments, of each user are passed on to the system to perform temporal analysis. The clustering with three and four number of clusters are found to be significant giving the representative groups. With three clusters, the representative group constitute of 82% of users and with four clusters, two representative groups are found having 45 and 36% of users. Analyzing these groups helps in finding the most popular behavior of users towards the concerned political party. Moreover, the groups perhaps tend to influence the opinion of other users in the network causing changes in their sentiments towards this party. The experimental results show that the proposed model has the power to distinguish behavior patterns of different individuals in a network.

20

Authors: Javeria Manzoor Shaikh; Khan Muhammad Brohi; Sabeen Qureshi

The built environment of hospital buildings are generally not accepted to be pleasant. In the design of healthcare facility, it is quite important that its design, spatial arrangement and areal distribution must respond to curative needs of people so as the outcome emerge in the form of healing environment in the physical spaces.This kind of healing environment is quite adequately available in the developed countries of the global north. However; in developing countries of the global south like Pakistan, the healing environment in healthcare facilities is neither documented nor evident in any available published literature. Whereas, it needs to be well documented and analyzed. Thus, this study aims to identify the healing environment in two selected hospital buildings in Pakistan that is ICP (Peshawar Institute of Cardiology) and FCP (FC Hospital Peshawar) by determining the percentage of wasted spaces within the building. The selected buildings are analyzed from the following aspects; circulation pattern in the hospital, accessibility, connectivity and barrier free movement within buildings, along with the walkability status of over stressed staff inside the hospital building while navigating, functionality of the schematic designs, the problem of the users concerning repetitiveness in their circulation pattern and the way to increase the efficiency of spaces, their spread and flow in the hospital building. In general, three key factors were investigated in this study, therefore, design determinents, areal distribution and adequate spatial organization. In this regard, total eight design determinants were investigated, i.e. entry, parking, waiting area, connectivity, visibility, walkability, accessibility, and way finding. Study approached the spatial simulation method therefore 3M analysis which is a Japanese model referred as Muda (waste), Muri (over burden), Mura (unevenness) based on the Kaizen theory for eliminating wasted spaces from Hospital buildings. Based on the findings and through the approached tools, the waste spaces within the hospital buildings were removed up to 40%.